HOW TO INSTALL A BATH TUB: INSTALL AN ACRYLIC TUB AND ALSO TUB SURROUND

How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround

How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround

Blog Article

Click Here To Find Out More

Everyone will have their private theory on the subject of How to Install a Bathtub.


Installing A Bathtub
Mounting a tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult project. If the old bathtub is readily easily accessible, the project can move immediately; if you need to open a wall surface to remove the old tub and also position the brand-new bathtub, the job is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly need an assistant to vacate the old tub as well as embeded in the new one. Ensure you have actually qualified yourself for the task and also are comfortable attempting it. As opposed to hiring a professional to take over a halfway-completed job, it is far better to take into consideration using one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This article will help you mount a brand-new bathtub in your bathroom if you have currently bought a new tub and don't need to alter the arrangement of your previous supply of water pipes.
Your tools as well as material checklist must make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Planning for the Installment


    To start with, the sustaining structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is important to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps device to avoid strain on the bathtub.
    Fit the adaptable tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of all of the supplied washing machines.
    Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its final placement.

    Removing Old Taps


    If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the restricted accessibility that is typically the situation.
    Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
    Prior to moving on to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.

    Mounting the Bathtub


    Utilizing both wooden boards under its feet, put the bathtub in the needed placement. The wood boards are valuable in uniformly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 small points.
    The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub up until the level reviews degree.
    To mount taps, fit the bottom of the furthest flexible tap port to the proper supply pipe by making a compression join; then do the same for the other tap.
    Switch on the supply of water as well as check all joints and new pipework for leaks as well as tighten them if essential. Load the bathtub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leaks.
    Finally, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the tub must wait up until the tub has been used a minimum of when as this will resolve it right into its last setting.

    Fitting New Touches


    If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a link to the existing supply pipes.
    If you need to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
    Next off, position the faucet in the placing opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Secure the faucet in place with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap ports. The previous kind must be linked to the faucet finishes first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Tub


    In the area where the bath meets the tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, creating the water to pass through the wall surface in between the bath and the tiling, leading to difficulties with moisture as well as feasible leaks to the ceiling below.
    You can pick from a range of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly load the bathtub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealer can crack rather early if you do not think about this motion prior to sealing.
    Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is suggested to fit the floor tiles utilizing waterproof or waterproof sticky and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    I discovered that post on Installing A Bathtub while doing a lookup on the search engines. Sharing is good. You just don't know, you may very well be helping someone out. Thanks a lot for your time. Visit again soon.




    Book 24/7


    Report this page